INT1EN=DISABLED, INT1SEL=INT1_0, INT0SEL=INT0_0, INT1POL=LOW, INT0POL=LOW, PGDONEF=NOT_SET, INT1MD=LEVEL, INT0EN=DISABLED, INT0MD=LEVEL
Global Port Control 0
| INT0SEL | External Interrupt 0 Pin Selection. 0 (INT0_0): Select INT0.0 1 (INT0_1): Select INT0.1 2 (INT0_2): Select INT0.2 3 (INT0_3): Select INT0.3 4 (INT0_4): Select INT0.4 5 (INT0_5): Select INT0.5 6 (INT0_6): Select INT0.6 7 (INT0_7): Select INT0.7 8 (INT0_8): Select INT0.8 9 (INT0_9): Select INT0.9 10 (INT0_10): Select INT0.10 11 (INT0_11): Select INT0.11 12 (INT0_12): Select INT0.12 13 (INT0_13): Select INT0.13 14 (INT0_14): Select INT0.14 15 (INT0_15): Select INT0.15 |
| INT0POL | External Interrupt 0 Polarity. 0 (LOW): A low value or falling edge on the selected pin will cause interrupt. 1 (HIGH): A high value or rising edge on the selected pin will cause interrupt. |
| INT0MD | External Interrupt 0 Mode. 0 (LEVEL): Interrupt on logic level at pin, as selected by the INT0POL field. 1 (EDGE): Interrupt on either rising or falling edge, as selected by the INT0POL field. 2 (DUAL_EDGE): Interrupt on both rising and falling edges (ignores INT0POL). |
| INT0EN | External Interrupt 0 Enable. 0 (DISABLED): Disable external interrupt 0. 1 (ENABLED): Enable external interrupt 0. |
| INT1SEL | External Interrupt 1 Pin Selection. 0 (INT1_0): Select INT1.0 1 (INT1_1): Select INT1.1 2 (INT1_2): Select INT1.2 3 (INT1_3): Select INT1.3 4 (INT1_4): Select INT1.4 5 (INT1_5): Select INT1.5 6 (INT1_6): Select INT1.6 7 (INT1_7): Select INT1.7 8 (INT1_8): Select INT1.8 9 (INT1_9): Select INT1.9 10 (INT1_10): Select INT1.10 11 (INT1_11): Select INT1.11 12 (INT1_12): Select INT1.12 13 (INT1_13): Select INT1.13 14 (INT1_14): Select INT1.14 15 (INT1_15): Select INT1.15 |
| INT1POL | External Interrupt 1 Polarity. 0 (LOW): A low value or falling edge on the selected pin will cause interrupt. 1 (HIGH): A high value or rising edge on the selected pin will cause interrupt. |
| INT1MD | External Interrupt 1 Mode. 0 (LEVEL): Interrupt on logic level at pin, as selected by the INT1POL field. 1 (EDGE): Interrupt on either rising or falling edge, as selected by the INT1POL field. 2 (DUAL_EDGE): Interrupt on both rising and falling edges (ignores INT1POL). |
| INT1EN | External Interrupt 1 Enable. 0 (DISABLED): Disable external interrupt 1. 1 (ENABLED): Enable external interrupt 1. |
| PGTIMER | Pulse Generator Timer. |
| PGDONEF | Pulse Generator Timer Done Flag. 0 (NOT_SET): Firmware has written to the PBPGPHASE register, but the Pulse Generator timer has not expired. 1 (SET): The Pulse Generator cycle finished since the last time PBPGPHASE was written. |